How to Drain a Pool with a Hose: Garden Hose Siphon and Pump Methods

Draining a pool with a garden hose uses the siphon principle – submerge the entire hose in pool water until fully filled with no air remaining, then move one end to a discharge point lower than the pool water surface and the weight difference between water in the hose and the lower endpoint maintains continuous flow without power or equipment. A standard 19 mm (3/4 inch) garden hose drains approximately 1,500-2,000 litres per hour under ideal conditions – sufficient for partial drains on above-ground and small pools but slow for full-volume drainage of inground pools where a submersible pump connected to a discharge hose (6,000-15,000 litres per hour capacity) is more practical. Both methods discharge water away from the pool through the hose to a suitable drain point.

This guide covers the garden hose siphon method step by step (two priming techniques), discharge hose connected to submersible pump, using pool filter waste port as fastest method for sand and DE filter pools, flow rate comparison by method, discharge location regulations in Portugal, partial drain versus full drain considerations, troubleshooting siphon failure, and natural pool water quality considerations when draining.

Key Takeaways

  • Siphon works by gravity – discharge end must be lower than pool water surface at all times
  • Full hose prime required – any air remaining in hose breaks siphon, water stops flowing
  • 19 mm garden hose: 1,500-2,000 litres per hour – adequate for small pools and partial drains
  • Submersible pump: 6,000-15,000 litres per hour – far faster for large or full-volume drains
  • Filter waste port: fastest method – uses pool pump, bypasses filter, large backwash hose
  • Discharge end must stay lower than pool surface – raising discharge end above pool level stops flow
  • Check local discharge regulations – chlorinated water may not be permitted to storm drains in Portugal
  • Siphon slows as water level drops – less height difference between pool and discharge reduces flow rate

Method 1: Garden Hose Siphon

How the Siphon Works

The siphon method involves submerging a hose into the pool, filling it with water, and then positioning one end at a lower elevation to create a siphoning effect. The difference in water levels naturally draws the water out.

The physics: water in the submerged portion of the hose is supported by pool water pressure. Water in the descending portion of the hose falls under gravity. As long as the discharge end sits lower than the pool water surface, the weight of falling water on the discharge side maintains continuous pull drawing pool water through the hose. The moment the discharge end rises above pool water level, flow stops.

Flow rate: Standard 19 mm (3/4 inch) garden hose generates approximately 1,500-2,000 litres per hour under siphon conditions. This drops progressively as pool water level falls – less height difference between pool surface and discharge point means less driving force.

Practical limits: For a 40,000-litre pool, full drainage via garden hose siphon takes 20-26 hours minimum under optimal conditions. More realistically 2-3 days accounting for slowing flow as water level drops. Suitable for partial drains (lowering water level 20-30 cm for chemistry adjustment) or small above-ground pools up to 10,000-15,000 litres.

Priming Method 1: Submersion Method (Most Reliable)

  1. Coil entire garden hose inside the pool with both ends submerged
  2. Allow hose to fill completely – watch for air bubbles rising from hose sections indicating incomplete filling
  3. Once no more bubbles rise and hose feels heavy throughout, pinch one end tightly with thumb and forefinger or fold hose back on itself creating a temporary seal
  4. Keeping that end sealed, lift it over the pool wall and lower it to discharge point (garden bed, storm drain, or sewer cleanout – see discharge regulations below)
  5. Release seal – siphon begins. Water flows continuously without further intervention

Why this method works reliably: Entire hose filled under water before positioning eliminates air pocket risk.

Priming Method 2: Fill from Tap (Faster Setup)

  1. Connect one end of garden hose to outdoor tap
  2. Place other end of hose into pool
  3. Turn tap on fully – water flows through hose filling it completely and entering pool
  4. Once water runs freely from pool end (no air bubbles, steady flow), quickly disconnect hose from tap while keeping pool end submerged
  5. Carry disconnected tap-end to discharge point, keeping it lower than pool water level
  6. Release – siphon begins

Risk: If disconnected end rises above pool water level even briefly during repositioning, air enters hose and breaks siphon. Work quickly between tap disconnection and placement at discharge point.

Maintaining the Siphon

Once established, the garden hose siphon runs unattended. Check every 30-60 minutes to verify:

Water still flowing: Place hand near discharge end – should feel consistent flow. Reduced or stopped flow indicates kinked hose, discharge end raised above pool level, or pool water level dropped below submerged hose intake.

Hose position: Discharge end must remain lower than pool water surface throughout the entire drain. As pool water level drops, maximum allowable height of discharge end drops proportionally.

No kinks: Sharp bends or kinks in the hose reduce or stop flow. Route hose in smooth curves without tight angles.

Intake submerged: Pool end of hose must remain below water surface. As water level drops, push the intake end toward the pool bottom to maintain submersion.

Multiple Hoses for Faster Drainage

For faster draining, use multiple hoses. Repeat the siphon technique for each hose.

Two hoses on double flow rate reach 3,000-4,000 litres per hour. Three hoses reach 4,500-6,000 litres per hour. Each hose requires independent priming. All discharge ends must be secured at lower elevation and kept separated to avoid flow interference.

Method 2: Submersible Pump with Discharge Hose

For pools above 15,000 litres or when time is limited, a submersible pump (sump pump) with discharge hose is significantly faster than a garden hose siphon.

Equipment

Submersible pump: Electric pump designed to operate fully submerged. Available from tool hire shops (€30-60 per day) or pool supply shops (€80-300 to purchase). Look for capacity specifications in litres per hour – residential pool drainage uses 6,000-15,000 litre per hour models.

Discharge hose: Connects to pump outlet, routes water to discharge point. Most pumps accept 32-38 mm (1.25-1.5 inch) discharge hose – larger than standard garden hose, significantly higher flow rate.

GFCI outlet: Submersible pump must connect to ground fault circuit interrupter (GFCI) protected outlet. Do not use standard unprotected outdoor outlets – electrical safety risk with water present.

Procedure

  1. Connect discharge hose firmly to pump outlet
  2. Route discharge hose to approved drainage point – ensure no kinks, no uphill sections that create back pressure
  3. Lower pump to deepest point of pool (deep end main drain area)
  4. Plug pump into GFCI outlet
  5. Verify water flowing from discharge hose end within 30 seconds
  6. Monitor pump every 15-20 minutes – pump must not run dry when water level drops below intake

Stopping before dry: When water level drops to 15-20 cm remaining, pump begins drawing air – audible change in motor tone (higher pitch, cavitation sound). Switch off immediately. Remove remaining water with a shop vacuum or mop and bucket.

Flow Rate Advantage

A 10,000 litre per hour submersible pump drains 40,000-litre pool in approximately 4 hours – versus 20-26 hours minimum with a single garden hose siphon. For large inground pools requiring complete drainage, submersible pumps are strongly recommended.

Method 3: Pool Filter Waste Port (Fastest Method)

For pools with sand or DE filters, the pool’s own pump and filter waste port drains water faster than any external equipment.

How it works: Set the multiport valve to the “Waste” position. Pool pump draws water from pool through skimmer and main drain, pushes through pump and filter, exits via waste port directly to drain rather than returning to pool. Uses full pump flow rate – typically 10,000-20,000 litres per hour for residential pumps.

Equipment needed: Backwash hose connected to waste port (25-38 mm diameter, 15-20 metre length typical). Most pool owners already have this for regular backwashing.

Procedure:

  1. Connect backwash hose to waste port on multiport valve
  2. Route hose to discharge point
  3. Set multiport valve to Waste position
  4. Start pool pump
  5. Verify water flowing from backwash hose end
  6. Monitor water level – pump must stop before water drops below skimmer mouth or pump runs dry

Limitation: Cannot drain below skimmer level – once water drops below skimmer opening, pump draws air. Remaining water below the skimmer requires a siphon hose or submersible pump to remove.

Not available for cartridge filters: Cartridge filter systems do not have a multiport valve with waste port. Use a submersible pump method.

Discharge Location and Regulations

Where to Discharge Pool Water

Municipal sewer cleanout: Safest and most common option for chlorinated pools. The cleanout access point in the garden or utility area connects to the wastewater system. Limit flow rate to avoid overwhelming sewer – maximum 45 litres per minute for residential connections.

Garden soil absorption: Acceptable for small volumes from partially drained pools. Large volumes can waterlog soil, kill plants, and cause erosion. Spread discharge across a large garden area using hose movement.

Storm drain: Regulated in Portugal (and most EU member states) – chlorinated pool water is not permitted to discharge to storm drains in most municipalities. Storm drains connect directly to rivers, streams, and ocean without treatment. Chlorine at pool concentrations (1-3 ppm) is acutely toxic to aquatic organisms.

Portuguese Regulations

EU Water Framework Directive and Portuguese water quality legislation (Lei da Água, Lei n.º 58/2005) regulate discharge of chemically treated water to natural water bodies and public drainage systems. Contact the local municipality (Câmara Municipal) to confirm the approved discharge method for your location before draining.

Dechlorination before discharge: If discharging to garden or permeable surface, allow free chlorine to fall below 0.5 ppm before draining. Stop adding chlorine 5-10 days before the planned drain, run the pump in sunlight to accelerate natural chlorine degradation. Sodium thiosulphate (dechlorinator) can speed the process – 2 grams per 1,000 litres reduces 3 ppm chlorine to near zero within 30 minutes.

Partial Drain Versus Full Drain

When Partial Drain is Sufficient

Most reasons pool owners drain pools do not require full drainage – partial drain achieves the goal with less time, less water waste, and lower risk.

High CYA (cyanuric acid above 80 ppm): Drain 30-50% and refill with fresh water. Dilutes CYA more effectively than any chemical treatment. Single garden hose siphon appropriate for this volume.

TDS (total dissolved solids) high: Same 30-50% partial drain and refill restores water balance.

Winter water level reduction: Lowering water 10-20 cm below skimmer for seasonal closure requires only partial drain – garden hose siphon or filter waste port for 15-20 minutes achieves this.

Post-rain overflow: Pool overfilled from heavy rainfall – siphon or waste port removes excess within 30-60 minutes.

When Full Drain is Required

Structural repair: Requires access to dry pool surface. Full drain necessary.

Liner replacement: Above-ground pools – must fully drain before liner removal.

Severe contamination: Flood debris, sewage backflow, chemical accident – full drain, cleaning, and refill required.

Gel coat resurfacing: Fiberglass pools – full drain needed for surface work.

Important for fiberglass pools: Never drain a fiberglass pool without assessing groundwater level first. Hydrostatic pressure from surrounding saturated soil can lift empty fiberglass shells from ground within hours of draining. Consult a professional before full drain of any inground pool.

Troubleshooting: Siphon Stops Working

Siphon starts then stops

Cause: Air entered the hose during setup or through a small crack in the hose wall.

Fix: Re-prime hose completely using submersion method, inspect hose for cracks or loose connections.

Water flows very slowly

Cause: Insufficient height difference between pool water surface and discharge point.

Fix: Lower discharge end closer to ground, redirect hose to lower-elevation point if available. Flow rate improves as discharge point goes lower.

Siphon will not start

Cause: Air remaining in hose sections, incomplete priming.

Fix: Use submersion method – coil the entire hose in the pool for 2-3 minutes before sealing the end and repositioning.

Siphon stops as pool empties

Normal: Flow rate reduces and eventually stops as pool water level approaches discharge end height. When pool surface height equals discharge end height, flow stops. Siphon cannot remove the final 15-30 cm of water in most ground-level pool configurations. Remove remaining water with a shop vacuum or mop.

Natural Pool Drainage Considerations

Natural swimming ponds from Oásis Biosistema do not require drainage at all.

No chemistry-driven drains: Conventional pools require periodic drainage to reset accumulated cyanuric acid, TDS, and chemical imbalance. Oásis Biosistema natural swimming ponds contain no chlorine, no stabiliser, and no chemical additives that accumulate over time. The biological filtration system – combining mechanical filtration, UV sterilisation, ozone technology, and beneficial bacteria – maintains water quality continuously without chemical input. Chemistry-driven drainage is eliminated entirely.

Water discharge advantage: When natural pond water is discharged – for structural maintenance or seasonal adjustment – it contains no chlorine, no chemical sanitisers, and no prohibited compounds. Discharge to garden soil, planted areas, or permeable surfaces is straightforward without dechlorination waiting periods. The water actively benefits surrounding soil and plants.

White quartz sand base: The special-grade white quartz sand used in Oásis Biosistema pond bases does not cloud water when disturbed during maintenance or partial draining. Its density means it settles rapidly, the bottom remains permanently visible, and drainage operations do not leave cloudy water or suspended sediment in the pond.

Oásis Biosistema designs natural swimming ponds where advanced filtration through UV sterilisation, ozone technology, and biological treatment maintains crystal-clear, chemical-free water without the accumulated chemical load that drives conventional pool drainage cycles, and where pond water – when discharged for maintenance – requires no dechlorination before returning to the surrounding Portuguese landscape.

Conclusion

Draining a pool with a garden hose uses siphon physics – submerge and fully prime the hose, position the discharge end lower than the pool water surface, and gravity maintains continuous flow at 1,500-2,000 litres per hour per hose without power or equipment. 

A submersible pump connected to a discharge hose is faster (6,000-15,000 litres per hour) and more practical for large or complete drains, while sand and DE filter pools can use the filter waste port – the fastest method, using the pool’s own pump at full flow rate. 

All methods must discharge to an approved point (municipal sewer cleanout for chlorinated water, or garden soil after dechlorination) following local Portuguese municipality guidance. 

Natural swimming ponds designed by Oásis Biosistema eliminate chemistry-driven drainage requirements entirely through biological filtration maintaining water quality without chemical accumulation, and discharge naturally chemical-free water directly to the surrounding landscape without regulatory restrictions in Portuguese pool installations.

FAQ

How to drain a pool with just a hose?

You can drain a pool using a garden hose by creating a siphon. Fill the hose with water, place one end in the pool, and position the other end lower than the water level. Gravity will pull the water out until the desired level is reached.

How to empty a swimming pool without a pump?

To empty a pool without a pump, use a siphon hose or garden hose. The discharge end must remain below the pool’s water level for the siphon to work. This method is slower than using a submersible pump but effective for small pools.

How to manually drain water from a pool?

Manual pool draining is typically done with a siphon hose or by using buckets for very small pools. Always direct the water to an approved drainage area and avoid completely draining fiberglass or vinyl pools unless recommended by the manufacturer.

How to siphon water upwards with a hose?

A standard siphon cannot move water higher than its source without assistance. It can briefly rise over an obstacle, but the outlet must end lower than the water level in the pool for gravity to keep the water flowing.