How to Drain a Fiberglass Pool: Risks, Methods, and Safety Guide

Draining a fiberglass pool is a high-risk procedure requiring groundwater assessment before starting, as hydrostatic pressure from surrounding saturated soil can lift an empty fiberglass shell out of the ground or crack the structure within hours. It can create damage costing €15,000-40,000 or more in shell replacement. When draining is unavoidable (major repairs, severe chemical imbalance, flood contamination), use a submersible pump at a controlled rate (maximum 45 litres per minute), open the hydrostatic relief valve in the main drain before the pool empties below 30 cm, drain only during dry weather with stable low groundwater, refill within 24 hours of reaching empty, and monitor continuously throughout the process, never leaving the pool unattended.

This guide covers why fiberglass pools should rarely be drained, hydrostatic pressure mechanics and damage types (shell lifting, cracking, buckling), groundwater assessment methods, step-by-step draining procedure using a submersible pump, hydrostatic relief valve function, water disposal regulations, gel coat and surface care during empty period, refilling procedure, situations requiring professional assistance, and natural pool drainage comparisons.

Key Takeaways

  • Fibreglass pools should rarely be drained – water weight stabilises shell. An empty shell is vulnerable to hydrostatic uplift.
  • Assess groundwater first – high water table makes draining extremely dangerous, may make it impossible.
  • Drain only in dry weather – no rain 48 hours before or during draining
  • Open hydrostatic relief valve – releases groundwater pressure before pool reaches empty
  • Submersible pump only – never drain using pool filter pump (risks running dry, motor damage)
  • Maximum 24 hours empty – refill as quickly as possible. UV and soil pressure damage accumulate rapidly
  • Never leave unattended – groundwater level can change rapidly, requiring immediate pump response
  • Professional recommended – most manufacturers and pool professionals advise against DIY draining

Why Draining a Fiberglass Pool Is Risky

Hydrostatic Pressure Mechanics

Definition: Hydrostatic pressure is the force exerted by groundwater in surrounding soil pressing against pool walls and floor from outside.

Normal operation: When the pool is full, water weight inside equals or exceeds groundwater pressure outside. When forces are balanced, the shell remains stable.

When empty: Removing pool water eliminates the internal counterforce holding the shell in place. Groundwater pressure acts unopposed against the shell exterior. In high water table conditions, this force can reach thousands of kilograms per square metre.

Result: Shell lifts upward (pops out of the ground), walls crack inward or outward, floor buckles, deck concrete around pool shifts and cracks.

Fiberglass-Specific Vulnerability

No structural rigidity without water: Unlike reinforced concrete pools (gunite/shotcrete), which are self-supporting structures, fibreglass shells depend on internal water pressure to maintain shape and position in soil.

Lightweight construction: Fiberglass shell weighs 900-1,800 kg depending on size. Groundwater pressure in saturated clay soil can generate uplift force of 5,000-15,000 kg on a standard 8m × 4m pool – easily overcoming shell weight.

Gel coat sensitivity: Exposed fiberglass gel coat surface degrades under direct UV radiation. Empty pools in summer sunlight develop oxidation, chalking, colour fade, and surface micro-cracking within 24-48 hours.

Damage costs: Structural damage from improper draining typically costs €15,000-40,000 for fiberglass shell replacement. Even partial lifting requires professional hydraulic re-seating and structural assessment.

When Draining Is Justified

Major structural repair: Cracks in shell requiring access from inside without water present.

Gel coat resurfacing: Complete gel coat renewal requires a dry, accessible surface.

Severe total dissolved solids (TDS): When TDS exceeds 2,500-3,000 ppm, partial or full drain and refill improves water balance. Note: partial draining (50%) significantly reduces risk versus full drain.

Flood contamination: Pool filled with mud, debris, or sewage-contaminated floodwater requiring full drain, cleaning, and refill.

Pool relocation: Rare, but occasionally pools are relocated during property redevelopment.

Not justified: Green water (treat with shock and algaecide), cloudy water (treat chemically), routine cleaning (vacuum and brush in water), scale deposits (treat with descaler), or any problem solvable without draining.

Groundwater Assessment Before Draining

Why Assessment Is Critical

Groundwater level determines whether draining is safe to proceed. Draining into high groundwater conditions causes immediate structural damage regardless of how carefully the procedure is performed.

Assessment Methods

Check recent rainfall: Avoid draining during or within 48-72 hours after significant rainfall. Soil remains saturated, groundwater elevated above normal baseline.

Observe surroundings: Signs of high groundwater include standing puddles in gardens away from irrigation, soft, waterlogged soil near pools, neighbouring properties with wet basements or crawl spaces.

Percolation test: Dig a test hole 60 cm deep adjacent to the pool. Check 24 hours later, if water is present in the hole, groundwater is too high for safe draining. If the hole remains dry, groundwater is likely below pool floor level.

Hydrostatic valve test (pools equipped): Open the hydrostatic relief valve in the main drain when the pool water level is above the valve. If water actively enters through the valve, groundwater is higher than the pool floor, so do not drain during this time.

Professional groundwater assessment: For high-risk sites (coastal, riverside, clay-heavy soil, previous flooding), commission professional hydrogeological assessment before proceeding.

Minimum Safety Conditions

Groundwater minimum 60 cm below pool floor: Provides adequate safety margin during draining process.

No rain forecast: 48 hours before and during draining (3-5 days ideal to allow soil moisture to stabilise).

Stable soil conditions: No recent excavation, construction, or ground disturbance adjacent to the pool area.

Dry season: Portugal’s dry summer months (June-September) are typically the safest window for draining. Autumn and winter rains elevate groundwater significantly.

Equipment Required

Submersible pump (sump pump): Primary draining equipment. Electric pump fully submerged in water, hose directs water to drainage point. Capacity: 150-500 litres per minute typical for pool draining use.

Never use pool filter pump for draining: Filter pump draws water from main drain through filter and waste line. Runs dry when water level drops below main drain intake, causing motor damage (€300-800 replacement). Pool filter pump not designed for draining function.

Discharge hose: 38-50 mm diameter hose directing water from submersible pump to discharge point. Length should reach approved drainage location without creating back-pressure kinks.

Hydrostatic relief valve key or screwdriver: For manually opening hydrostatic valve in main drain before pool reaches empty.

Submersible pump for groundwater (if equipped): If the pool has a dewatering system or sump pit adjacent to the pool, operate this pump throughout draining, keeping groundwater level below pool floor.

Water testing kit: Test pool water before full drain. Verify whether partial drain and refill achieves chemistry goals (often sufficient).

Step-by-Step Draining Procedure

Step 1: Verify Safety Conditions

Confirm groundwater assessment is complete (dry soil, no recent rainfall, percolation test passed). Check the 48-hour weather forecast and make sure there’s no rain predicted. Notify the pool manufacturer or professional installer of intended draining (some warranties require notification).

Step 2: Plan Discharge Location

Legal requirements: Pool water discharge is regulated in Portugal and most EU countries. Contact the local municipality (Câmara Municipal) to verify approved discharge points.

Options:

  • Municipal sewer via cleanout access point (most common) – limit flow to 45 litres per minute to avoid overwhelming sewer capacity
  • Stormwater drain (check local regulations – chemically treated pool water often prohibited from stormwater systems)
  • Permeable garden area away from pool (large volumes may cause local flooding or soil erosion)
  • Tanker removal (professional service, expensive, required in sensitive environmental zones)

Check chemical levels: If pool water contains high chlorine levels, allow it to neutralise (dechlorinate) before discharge. Chlorine above 1 ppm is harmful to watercourses. Leave the pump running through the filter for 24-48 hours without adding chemicals to reduce chlorine naturally before draining, or add sodium thiosulphate (dechlorinating agent).

Step 3: Shut Down Pool Equipment

Turn off the pool pump and heater at the circuit breaker. Set the multiport valve to a closed position. Pool equipment must not operate during draining, as low water level causes pumps to run dry.

Step 4: Place Submersible Pump

Lower the submersible pump to the deepest point of the pool (main drain area in deep end). Connect discharge hose routing to approved discharge location. Ensure hose lies flat without kinks or uphill sections creating back-pressure.

Step 5: Begin Draining at Controlled Rate

Start a submersible pump. Monitor flow rate. Maximum 45 litres per minute for standard residential fiberglass pools. Higher flow rates create a rapid pressure differential that can stress the shell before groundwater pressure equalises.

Monitor continuously: Do not leave the pool unattended. Check every 15-20 minutes that discharge hose flowing freely, no unusual noises from pump (indicating air ingestion at low water level), no visible ground movement or cracking around pool perimeter.

Watch for groundwater signs: If groundwater begins rising into the pool during draining (water level stops dropping or rises despite the pump running), stop immediately, as it means conditions are unsafe and groundwater pressure is too high.

Step 6: Open Hydrostatic Relief Valve

When the water level reaches approximately 30 cm (12 inches) depth, open a hydrostatic relief valve located in the main drain at the pool floor. This is critical. Opening the valve before the pool is nearly empty allows groundwater to trickle up through the valve into the pool, equalising pressure rather than building to dangerous levels.

Valve types: Some pools have manually operated valves (screw or twist to open). Others open automatically when external pressure exceeds internal pressure. Consult pool manufacturer documentation for your specific system.

If no hydrostatic valve is present: Standard dewatering procedure requires drilling a 12 mm hole in the pool floor at the deepest point before draining to provide groundwater pressure relief. This hole is plugged and sealed after refilling. Consult a professional before proceeding with this method.

Step 7: Complete Drainage and Immediate Inspection

Once the pool reaches minimum water level (pump can no longer operate without drawing air), remove pump and remaining water with mop, squeegee, or wet-dry vacuum. Remove all water – standing water during cleaning causes streaking and mineral deposits on the gel coat.

Immediate inspection: With pool empty, inspect entire shell interior for:

  • Cracks (hairline fractures, structural cracks, star cracks around fittings)
  • Blistering (osmotic blisters appearing as raised bubbles in gel coat)
  • Delamination (gel coat separating from fiberglass substrate)
  • Discolouration and staining
  • Fitting integrity (main drain, returns, skimmer throat)

Document all findings with photographs before cleaning. Professional assessment may be needed before refilling.

Step 8: Clean and Repair

Gel coat cleaning: Use non-abrasive pool surface cleaner and a soft cloth or sponge. Avoid pressure washing (damages gel coat, forces water into osmotic blisters). Avoid acidic cleaners (muriatic acid, vinegar).

Stain removal: Enzyme-based stain remover for organic stains (leaf tannins, algae). Metal stain remover for rust or copper deposits. Follow manufacturer instructions for gel coat compatibility.

Repairs: Hairline surface cracks in gel coat repaired with gel coat repair kit (colour-matched to pool). Structural cracks or large fractures require professional fiberglass repair. Do not refill until structural integrity is confirmed.

Time limit: Complete all cleaning and repairs and begin refilling within 24 hours of reaching empty, wherever possible. UV exposure and ongoing groundwater pressure risk increase significantly beyond 24 hours.

Step 9: Refill Procedure

Close hydrostatic relief valve (or reinstall plug in drilled hole) before beginning refill. If left open, groundwater will flow in faster than the hose fills, creating muddy, contaminated water.

Fill using a garden hose or water delivery service. Direct hose toward the pool floor or steps and not against walls or into the deep end from height. Falling water impact can stress fiberglass shells and create turbulence, stirring remaining debris.

Refill speed: No maximum speed restriction for refilling (internal pressure increases as water level rises, reducing risk). Fill as quickly as water supply allows.

Chemistry on refill: Add sequestrant (metal treatment) to the first few inches of water before full refill. This prevents metal staining as fresh water contacts pool surfaces. Once full, balance: pH 7.2-7.6, alkalinity 80-120 ppm, calcium hardness 250-400 ppm, then sanitise.

Partial Draining: Lower-Risk Alternative

When chemistry adjustment requires dilution (high TDS, CYA above 100 ppm), partial draining (30-50% of pool volume) achieves dilution while significantly reducing hydrostatic pressure risk.

Procedure: Drain pool to halfway point only using submersible pump. Monitor groundwater indicators throughout. Refill with fresh water. Retest and balance chemistry. Repeat if required (two 50% drains achieve 75% dilution).

Advantages: Maintains substantial internal water pressure throughout, reduces exposure time, reduces UV exposure risk, retains some treated water reducing chemical cost of full refill.

When to Call a Professional

High water table sites: Coastal properties (Algarve, Lisbon coast), riverside lots, low-lying areas.

No hydrostatic valve installed: Requires professional assessment of the safest dewatering method.

Previous structural damage: Any existing cracks, movement, or settlement require professional assessment before draining adds stress.

Structural repairs required: Fiberglass shell repair requiring lamination or structural patching needs professional completion.

No suitable discharge location: Legal and safe discharge options unavailable without a professional drainage contractor.

Manufacturer warranty: Many fiberglass pool warranties specify professional involvement for draining to maintain warranty validity.

Natural Swimming Pools and Draining

Natural swimming pools require draining even less frequently than conventional pools due to biological filtration eliminating chemical imbalance problems that typically necessitate conventional pool drainage.

No TDS accumulation: Natural pools contain no dissolved salts, chlorine compounds, cyanuric acid, or chemical additives that accumulate over time, degrading water quality. TDS remains naturally low from rainfall and fresh water topping-up only.

No chemical overload: Conventional pools require draining when chemicals build up beyond recoverable balance. Natural pools maintain balance through biological processes without chemical additions. This trigger for draining is eliminated entirely.

Regeneration zone management: Biological filtration via planted regeneration zones handles organic load continuously. Algae are controlled through nutrient competition rather than chemical shock requiring dilution drain.

Rare structural drain: Natural pools may require draining for structural repairs on the same schedule as conventional pools (every 10-15 years typical), but all chemistry-related draining triggers are absent.

Oásis Biosistema designs natural swimming pools using biological filtration through planted regeneration zones that eliminate chemical accumulation requiring draining, reducing pool drainage frequency to structural necessity only and providing chemical-free water management in Portuguese landscape installations.

Conclusion

Draining a fiberglass pool requires groundwater assessment (percolation test, dry weather minimum 48 hours, no rain forecast) confirming conditions are safe before beginning, using a submersible pump at maximum 45 litres per minute directed to an approved discharge point, opening the hydrostatic relief valve when water reaches 30 cm depth to prevent structural uplift damage, completing cleaning and repairs within 24 hours, and refilling immediately, adding sequestrant before chemistry balancing. 

Hydrostatic pressure from surrounding saturated soil can lift an empty fiberglass shell out of the ground or crack the structure, costing €15,000-40,000 in replacement, making draining high-risk and justified only for major structural repair, gel coat resurfacing, severe TDS accumulation, or flood contamination – all other pool problems should be resolved chemically without draining. 

Natural swimming pools designed by Oásis Biosistema eliminate chemistry-driven draining requirements through biological filtration in planted regeneration zones, maintaining water quality without chemical accumulation and reducing draining events to structural necessity only in chemical-free Portuguese pool installations.

FAQ

Can you safely drain a fiberglass pool?

Yes, but with caution. A fiberglass pool should not be completely drained unless necessary, and conditions are safe. High groundwater pressure can cause the pool shell to shift, crack, or even lift out of the ground.

Do fiberglass pools have main drains?

Many fiberglass pool designs include one or two main drains at the deepest point, although some newer pools rely more heavily on skimmers and advanced circulation systems instead of traditional main drains.

How far down can I drain my fiberglass pool?

In most cases, you should not lower the water more than 12–18 inches (30–45 cm) below the skimmer unless specifically recommended by the manufacturer. Completely draining a fiberglass pool should generally be left to professionals.

Do you drain a fiberglass pool for winter?

No, fiberglass pool pools are typically not drained for winter. Instead, the water level is lowered slightly, plumbing lines are winterised, chemicals are balanced, and a winter cover is installed to protect the pool.