How to Drain a Pool with a Cartridge Filter: Methods and Step-by-Step Guide

Draining a pool with a cartridge filter is different from draining a pool with a sand or DE filter because cartridge filters have no multiport valve and no waste port – the fastest sand filter drainage method (setting the valve to Waste and running the pool pump) is not available. Cartridge filter pool owners must use one of three alternative methods: submersible pump (fastest, 6,000-15,000 litres per hour), garden hose siphon (no equipment required, 1,500-2,000 litres per hour), or the cartridge filter drain plug method where the pool pump pushes water out through the filter’s own drain port with a hose connected to it. Understanding which method applies to your setup and pool size determines how quickly and efficiently the drain is completed.

This guide covers why cartridge filters cannot use the waste port method, the three available drainage methods with step-by-step procedures, the filter drain plug technique and its limitations, partial drain versus full drain considerations, discharge location requirements in Portugal, what to do with the cartridge during and after draining, and natural pool drainage considerations.

Key Takeaways

  • No waste port on cartridge filters – cannot set to Waste like sand/DE filters, pool pump cannot drain directly
  • Three methods available: submersible pump (fastest), garden hose siphon (no equipment), filter drain plug (moderate speed)
  • Submersible pump: 6,000-15,000 litres per hour – best option for large pools or full drains
  • Garden hose siphon: 1,500-2,000 litres per hour – practical for partial drains, no pump needed
  • Filter drain plug method: remove cartridge first, connect hose to drain port, run pool pump – moderate flow rate
  • Turn off pump before opening filter – opening housing under pressure causes water to flood equipment area
  • Remove cartridge before drainage – prevents debris from lodging against cartridge during drain flow
  • Discharge to approved point – chlorinated water requires sewer connection, not storm drain

Why Cartridge Filters Cannot Use the Waste Port Method

Sand filters and DE filters have a multiport valve – a rotating valve with multiple settings including Waste, which redirects water from the pool pump straight out to a backwash hose bypassing the filter entirely. Setting a sand filter to Waste and running the pool pump drains water at full pump flow rate (10,000-20,000 litres per hour for most residential pumps) – the fastest pool drainage method available.

Cartridge filters do not have a multiport valve, so the method depends on your specific setup. The cartridge filter housing has an inlet, an outlet, and a drain plug at the base, but no valve to redirect flow to waste. Running the pool pump with a cartridge filter simply circulates water through the filter and back to the pool as normal – it does not drain the pool.

This is the single most important distinction cartridge filter owners need to understand before attempting pool drainage. Attempting to drain through the normal filtration circuit achieves nothing – water cycles continuously through the system and returns to the pool.

A submersible pump (sump pump) placed in the pool and connected to a discharge hose is the fastest and most practical method for cartridge filter pools requiring significant drainage.

Equipment

Submersible pump: Available from tool hire shops (€30-60 per day) or pool supply retailers (€80-300 to purchase). Capacity rated in litres per hour – residential pool drainage requires 6,000-15,000 litre per hour models for reasonable speed. Larger capacity pumps drain faster but cost more to hire.

Discharge hose: 32-50 mm diameter hose connecting to pump outlet. Route to approved discharge point. Ensure no uphill sections or kinks that create back pressure reducing pump efficiency.

GFCI protected outlet: Submersible pump must connect to a ground fault circuit interrupter protected outlet. Never plug into a standard unprotected outdoor socket with water present – electrocution risk.

Step-by-Step Procedure

  1. Turn off pool pump and filter at circuit breaker
  2. Connect discharge hose firmly to submersible pump outlet – hand tight plus quarter turn
  3. Route discharge hose to approved drainage point (municipal sewer cleanout – see discharge section below)
  4. Lower submersible pump to deepest point of pool (main drain area in deep end) – secure with rope if pool deep
  5. Plug pump into GFCI outlet
  6. Verify water flowing from discharge hose end within 30 seconds – if not, check hose connections and power supply
  7. Monitor pump every 15-20 minutes throughout drainage
  8. When water level drops to 15-20 cm remaining, the pump begins drawing air – audible change in motor tone (higher pitch cavitation sound). Switch off immediately to prevent motor damage
  9. Remove remaining water with shop vacuum, mop, or bucket

Partial Drain with Submersible Pump

For partial drains (reducing water level to adjust chemistry, lower for winter closure, remove post-rain overflow), the submersible pump is equally suitable. Place the pump in the pool, set a timer or watch water level closely, and switch off when target depth is reached. Much more controllable than the filter drain plug method for partial drains.

Method 2: Garden Hose Siphon (No Equipment Required)

Garden hose siphon requires no additional equipment and costs nothing – useful for partial drains, small pools, or when a submersible pump is unavailable.

How the Siphon Works

Submerging a garden hose completely fills it with water. Positioning the discharge end lower than the pool water surface creates a weight imbalance – water on the discharge side falls, pulling pool water continuously through the hose. The siphon runs unassisted as long as the discharge end stays lower than pool water level.

Flow rate: Standard 19 mm (3/4 inch) garden hose generates 1,500-2,000 litres per hour. Reduces progressively as pool water level drops and height difference between pool surface and discharge point decreases.

Priming Method: Full Submersion (Most Reliable)

  1. Coil entire garden hose inside pool with both ends submerged
  2. Allow 2-3 minutes for hose to fill completely – air bubbles rising from hose sections indicate incomplete filling
  3. Once no more bubbles rise, pinch one end tightly or fold back on itself to seal
  4. Lift sealed end over pool wall, lower to discharge point (ground level or lower)
  5. Release seal – siphon begins. Water flows continuously without further power or attention

Maintaining the Siphon

Check every 30-60 minutes. Discharge end must remain lower than pool water surface at all times – as pool level drops, available height difference decreases. Siphon stops when pool surface height equals discharge point height. Remove the final 10-15 cm with shop vacuum or mop – siphon cannot remove the last section of water in most installations.

Best for: Partial drains of 10,000-20,000 litres on small to medium pools. Full drainage of large pools via siphon takes 2-3 days minimum.

Method 3: Cartridge Filter Drain Plug Method

Some cartridge filter housings have a drain plug at the base that, when removed and fitted with a hose connection, allows the pool pump to push water out through the filter base instead of back to the pool.

If your system has a drain plug at the back of the filter housing, shut off the pump, unscrew the plug, then restart the pump and let it run until the water drops to where you want it.

When This Method Applies

Not all cartridge filter housings have an accessible drain plug sized appropriately for hose connection. Check filter housing base – if a 38 mm (1.5 inch) or larger threaded drain port is present and accessible, this method is viable. Smaller inspection ports do not generate adequate flow rate for practical drainage.

Step-by-Step Procedure

  1. Turn off pool pump at circuit breaker
  2. Open filter housing: unscrew clamp band or twist-lock collar on top of filter tank
  3. Remove cartridge from housing – set aside for cleaning (see cartridge section below)
  4. Replace filter housing lid loosely – keeps system partially pressurised while allowing air in
  5. Unscrew drain plug from filter housing base
  6. Thread a hose adapter fitting into drain port (38 mm to garden hose adapter, available from plumbing suppliers, €5-15)
  7. Connect garden hose or discharge hose to adapter
  8. Route hose to approved discharge point
  9. Turn pool pump on at circuit breaker
  10. Water flows from pool through pump into filter housing and out through drain port hose
  11. Monitor continuously – pump must stop before water drops below skimmer mouth (pool pump draws air from skimmer, damages motor seals)
  12. When water reaches target level or approaches skimmer, shut off pump at circuit breaker

Limitations of This Method

Below skimmer level: Pool pump draws water from skimmer. Once water level drops below the skimmer opening, the pump draws air rather than water – the pump runs dry causing seal and impeller damage. This method cannot drain below skimmer level.

Flow rate: Filter drain port method uses pool pump flow rate but restricted by drain plug port size. Actual flow rate depends on pump capacity and port diameter – typically 3,000-8,000 litres per hour.

Monitoring required: Cannot leave pool unattended during this method. Water level drops continuously and must be watched to stop the pump before the skimmer draws air.

Removing Water Below Skimmer Level

All three methods above stop at or above skimmer level. For winterisation, structural repair, or complete drainage requiring water removal below the skimmer, use:

Submersible pump in deep end: Lower pump to pool floor in deep end. Operates independently of pool plumbing – not affected by skimmer air draw. Continue draining to near-empty.

Garden hose siphon from deep end: Submerge siphon hose intake at deep end floor. Siphon continues as long as water covers intake – can drain to within 5-10 cm of the pool floor.

Final residual water: Last 5-10 cm cannot be reached by any pump or siphon effectively. Remove with shop vacuum (wet-dry vacuum on suction setting), mop and bucket, or absorbent sponges. For fiberglass pools, ensure all residual water is removed before leaving the pool empty – standing water during an empty period causes mineral deposits and differential drying stress.

What to Do with the Cartridge During Drainage

Remove Before Major Drainage

For full drains or drains lasting several hours, remove cartridges from housing before starting.

Reasons: During heavy drain flow, debris dislodged from the pool floor can be drawn into filter housing and compact against cartridge pleats, causing damage and reducing filter life. Removing cartridges before drainage prevents this debris compaction.

Procedure: Turn off pump, open housing (unscrew clamp or twist-lock), lift cartridge out, close housing loosely.

Clean Cartridge During Drain Time

Use the drainage period productively and while the pool drains, clean the cartridge.

Rinse: Garden hose high-pressure rinse between all pleats from top to bottom, rotating cartridge. Remove all visible debris.

Soak (for seasonal or deep clean): Soak in commercial filter cleaning solution (diluted according to product instructions) or 100 ml bleach per 10 litres water for 2-4 hours. Dissolves body oils, sunscreen, and fine debris that hose rinsing does not reach.

Rinse again: Thorough hose rinse after soaking – remove all cleaning solution residue before reinstalling. Cleaning chemical residue in the pool causes cloudiness and chemistry disruption.

Inspect: Check cartridge pleats for tears, compressed sections, or collapsed core. Damaged cartridges pass particles into pool water – replace if any structural damage is found.

Dry: If storing cartridge (winter closure), allow it to dry completely before storage in a dry indoor location. Storing a damp cartridge promotes mold growth on filter media.

Reinstall After Drainage

Once pool refilled to correct level: reinstall cleaned cartridge, close housing, ensure clamp band or lock collar tightened correctly (finger tight plus quarter turn – no tools needed for most models), restore drain plug, restore all electrical power, prime pool pump by filling strainer pot with water before starting.

Discharge Location Requirements

Approved Discharge Points

Municipal sewer cleanout: Cleanout access point in garden connects to wastewater system. Standard approved method for chlorinated pool water. Limit flow rate to maximum 45 litres per minute to avoid overloading residential connections.

Garden soil absorption: Acceptable for small partial drains (under 5,000 litres) at low chlorine levels (below 1 ppm). Large volumes waterlog soil and can damage plants. Chlorine above 1 ppm is harmful to plant roots and soil bacteria – dechlorinate before garden discharge.

Storm drain: Not permitted for chlorinated pool water in Portugal and throughout the EU. Storm drainage routes directly to rivers, streams, and coastal waters without treatment. Chlorine at pool concentrations is acutely toxic to aquatic organisms. EU Water Framework Directive and Portuguese Lei da Água (Lei n.º 58/2005) prohibit chemical discharge to natural water bodies.

Dechlorinating Before Discharge

If discharging to garden or permeable surfaces, reduce chlorine to below 0.5 ppm before draining.

Stop adding chlorine 5-10 days before planned drain and allow natural UV degradation to reduce levels. Alternatively, add sodium thiosulphate dechlorinator (2 grams per 1,000 litres reduces 3 ppm chlorine to near zero within 30 minutes). Test chlorine level before beginning drain to confirm adequate reduction.

Partial Drain: The Most Common Use Case

Full drainage of inground pools carries risk (hydrostatic uplift for fiberglass, groundwater pressure for all pool types) and is rarely necessary. Most reasons pool owners drain pools require only partial drainage.

CYA (cyanuric acid) above 80 ppm: Drain 30-50% and refill. Dilutes cyanuric acid more effectively than any chemical treatment. A single submersible pump session or garden hose siphon handles this volume.

Post-rain overflow: Pool overfilled from heavy rainfall – submersible pump or siphon for 30-60 minutes lowers water to correct level.

Winter water level reduction: Lower pool 10-20 cm below skimmer for seasonal closure. Filter drain plug method or submersible pump for 15-30 minutes achieves this.

Salt or TDS reduction: 30-50% drain and refill reduces total dissolved solids. Submersible pump practical for this volume.

Natural Pool Drainage Considerations

Natural swimming ponds designed by Oásis Biosistema require drainage far less frequently than conventional cartridge filter pools, and with significant practical advantages when drainage is performed.

No chemistry-driven drainage: The primary reasons conventional pools require drainage – accumulated cyanuric acid from stabilised chlorine products, high TDS from chemical additions, salt build-up – are entirely absent in an Oásis Biosistema natural swimming pond. The system combines mechanical filtration, UV sterilisation, ozone technology, and beneficial bacteria to maintain water quality continuously without any chemical additions. No chemicals enter the water, none accumulate, and chemistry-driven partial drains are eliminated.

Simpler discharge: When natural pond water is discharged for structural maintenance, the water contains no chlorine, no stabiliser, no algaecides, and no chemical sanitisers. It can be discharged directly to garden soil and planted areas without dechlorination waiting periods, without regulatory concern, and with benefit to surrounding plants. The white quartz sand base used in Oásis Biosistema pond construction does not cloud the water when disturbed – drainage and any associated bottom disturbance does not create suspended sediment that takes days to settle.

No cartridge filter management during drainage: Oásis Biosistema natural swimming ponds do not use cartridge filter systems. The biological filtration approach with UV sterilisation, ozone, and mechanical filtration integrated into the pond system operates differently, and drainage does not require cartridge removal, cleaning, or storage as an additional procedure.

Discover how Oásis Biosistema natural swimming ponds eliminate chemistry-driven drainage cycles through biological water treatment, maintaining crystal-clear water year-round without chemical accumulation in Portuguese landscape installations.

Conclusion

Draining a pool with a cartridge filter requires a submersible pump (6,000-15,000 litres per hour, recommended for large or full drains), garden hose siphon (1,500-2,000 litres per hour, no equipment required, suitable for partial drains), or the filter drain plug method (remove cartridge, connect hose to filter base drain port, run pool pump until water reaches skimmer level). 

The sand filter waste port method is not available as cartridge filters have no multiport valve. All methods discharge to an approved point – municipal sewer cleanout for chlorinated water, or garden soil after dechlorination to below 0.5 ppm – following Portuguese municipal regulations. Cartridge should be removed before major drains to prevent debris compaction against pleats, and cleaned thoroughly during the drain period before reinspection and storage or reinstallation.

FAQ

How to empty a pool with a cartridge filter?

Most cartridge filter systems cannot be used to drain a pool because they do not have a “waste” setting. To lower the water level, use a submersible pump or siphon hose instead of running water through the filter.

How do you vacuum a pool to waste with a cartridge filter?

You generally cannot vacuum to waste with a cartridge filter. Unlike sand or DE filters, cartridge filters lack a waste mode. To remove debris without sending it through the filter, use a portable waste pump or a dedicated vacuum-to-waste setup.

Can you drain a pool through the filter?

No, most cartridge filters are not designed for draining pools. Running the system to empty the pool may damage the pump or filter. A submersible pump or siphon is the safest method for draining water.

How to close a pool with a cartridge filter?

To winterize a pool with a cartridge filter, clean the filter cartridge, drain the pump and filter housing, remove drain plugs, lower the water level if needed, balance the water chemistry, add winterizing chemicals, and securely install the pool cover.